---

Boron		0.015 min
Carbon		0.05 - 0.15
Chromium		20 - 24
Cobalt		Balance
Iron		3 max
Lanthium		0.02 - 0.12
Manganese		1.25 max
Nickel		20 - 24
Silicon		0.2 - 0.5
Tungsten		13 - 15

Principal Design Features		This is a cobalt-nickel-chromium-tungsten alloy designed for high temperature strength and resistance to oxidation at temperatures up to 2000 F(1095 C).

Applications		While primarily employed in the aerospace industry, this alloy has found uses in commercial industrial applications including land-based gas turbines. Generally found in hot sections of engines in burner cans, ducting and afterburner components. In recent years, it has been eclipsed by Alloy 230 for many applications due to improved properties.

Machinability		Conventional machining techniques used for iron based alloys may be used. This alloy does work-harden during machining and has higher strength and "gumminess" not typical of steels. Heavy duty machining equipment and tooling should be used to minimize chatter or work-hardening of the alloy ahead of the cutting. Most any commercial coolant may be used in the machining operations. Water-base coolants are preferred for high speed operations such as turning, grinding, or milling. Heavy lubricants work best for drilling, tapping, broaching or boring. Turning: Carbide tools are recommended for turning with a continuous cut. High-speed steel tooling should be used for interrupted cuts and for smooth finishing to close tolerance. Tools should have a positive rake angle. Drilling: Steady feed rates must be used to avoid work hardening due to dwelling of the drill on the metal. Rigid set-ups are essential with as short a stub drill as feasible. Heavy-duty, high-speed steel drills with a heavy web are recommended. Feeds vary from 0.0007 inch per rev. for holes of less than 1/16" diameter, 0.003 inch per rev. for 1/4" dia., to 0.010 inch per rev. for holes of 7/8"diameter. Milling: To obtain good accuracy and a smooth finish it is essential to have rigid machines and fixtures and sharp cutting tools. High-speed steel cutters such as M-2 or M-10 work best with cutting speeds of 30-40 feet per minute and feed of 0.004"-0.006" per cutting tooth. Grinding: The alloy should be wet ground and aluminum oxide wheels or belts are preferred.r 1/4" dia., t0 degrees to the joint. For Short-Circuiting-Transfer GMAW a typical voltage is 18-22 with a current of 75-150 amps and a wire feed of 8-10 inches per minute. Submerged-Arc Welding: Generally submerged-arc welding should be avoided. This weld process involves high heat input and may lead to cracking of the alloy workpiece.

Forming		This alloy has good ductility and may be readily formed by all conventional methods. Because the alloy is stronger than regular steel it requires more powerful equipment to accomplish forming. Heavy-duty lubricants should be used during cold forming. It is essential to thoroughly clean the part of all traces of lubricant after forming as embrittlement of the alloy may occur at high temperatures if lubricant is left on. The alloy will work harden rapidly and intermediate annealing may be required for extensive forming operations.

Welding		This alloy can be readily welded using MIG, TIG, electron beam and resistance techniques.

Heat Treatment		Solution heat treat at 2150 F (1175 C) and cool rapidly. Annealing at temperatures below this may cause carbide precipitation resulting in deleterious effects on properties.

Forging		Soak thoroughly at 2150 F (1175 C), followed by rapid post-work cooling.

Cold Working		This alloy can be readily cold formed using all common techniques. Its high work hardening rate will require intermediate annealing for extensive deformation.

Physical Data : [top]

Density (lb / cu. in.)	0.324
Specific Gravity	8.97
Specific Heat (Btu/lb/Deg F - [32-212 Deg F])	0.101
Electrical Resistivity (microhm-cm (at 68 Deg F))	554
Melting Point (Deg F)	2425
Modulus of Elasticity Tension	33.6

Form		Sheet
Condition		Solution Annealed
Temper		70
Tensile Strength		139
Yield Strength		70
Elongation		56
Form		Sheet
Condition		Solution Annealed
Temper		1200
Tensile Strength		103
Yield Strength		44
Elongation		61
Form		Sheet
Condition		Solution Annealed
Temper		1400
Tensile Strength		92
Yield Strength		42
Elongation		43
Form		Sheet
Condition		Solution Annealed
Temper		1600
Tensile Strength		61
Yield Strength		38
Elongation		73